![CineSticks Starter Pack - 70pcs - WS - ScottyMakesStuff](http://eu.scottymakesstuff.com/cdn/shop/products/standard_95f7c527-a2b8-435a-9ae1-f1667d83ecb2_{width}x.jpg?v=1666782100)
CineSticks Starter Pack - 70pcs - WS
- Fast shipping
- In stock, ready to ship
- Inventory on the way
Wholesale Multi SKU Packs of CineSticks - 70 pieces
A starter pack of our CineSticks.
30x CS-N1 - DJI RC-N1 Controller, DJI Smart, Mavic 2, Mini 1,2&SE, Air1,2&2S + More
20x CS-RC2 - DJI RC Controller
10x CS-RCP - DJI RC Pro, Autel Smart & DJI Grey FPV
5x CS-PN1 - DJI Phantom and Inspire Controllers
2x CS-AE - Autel EVO II + More
3x CS-M1 - Mavic 1, 2, and Air, DJI Spark + More
+Spare Parts Kit
The new CineSticks design is more compact giving you more control over your drone than ever before!
You'll be able to achieve those cinematic movements such as pans, dollies, and tilts without any little jitters that are so hard to avoid with standard joysticks.
We use super soft silicone rubber to give you the smooth motion your video needs. But that's not all, we made them with adjustable resistance, allowing you to fine-tune the sensitivity of your sticks.
Check out our videos showcasing how CineSticks will enhance your videos!
Video Reviews
Note: These are for the CineStick R2 version but the effective smoothing will be very similar.
Matt Holder from Reflex Films Australia in Perth, shows us why CineSticks give him that winning advantage with their drone footage.
The well known Italian Youtube personality, Bighenet, gives his verdict on the new resistive joysticks called CineSticks.
Italian Drone YouTuber David Ulivelli
Ernst Markus Kofler
Hawaiian Drone YouTuber Atort Aerials
How to use
To attach the CineSticks,
- first, unscrew your current joysticks, then take the threaded rods and screw the small threaded end into your joystick threaded holes
- Take the silicone rubber 'boots' and the alloy silicone caps and push the caps onto the top of the boots. You may need to push them on using a screwing action.
- Push the boots over the threaded rods.
- Screw the knobs on top of the exposed threaded rod and push fully down to expose the threaded rod ends.
- Finally, screw in the knobs and adjust down until you get to the desired firmness.
To increase the firmness/resistance, you just screw down the knob of the joystick. To soften/decrease the resistance, pinch the neck of the silicone rubber and unscrew the stick.
To Remove the CineSticks,
- Just pinch the neck of the silicone rubber and unscrew the knob until it screws off.
- Pull the silicone boots off.
- Finally, unscrew the threaded rods.
Compatibility:
DJI RC Controller
More coming once tested. If you successfully test these CineSticks on a controller not covered in this list then please let us know by emailing customerservice@scottymakesstuff.com so we can add it to this list.
Guide in PDF format: CineSticks RC Instructions
Note: When using the CineSticks, particularly at higher resistance, letting go of the joysticks may not return to the centre exactly. Instead, you should bring the CineSticks back to the centre and then confirm visually that there is no drift. For controllers that perform a pre-flight stick check, it’s best to start up with the CineSticks at low resistance before increasing resistance. It’s recommended that you store the CineSticks with the resistance off to keep your CineSticks performing at their best.
Always reduce resistance by first pinching or pushing on the side of the rubber boot. Not doing so can unscrew the threaded rod from the controller, reducing its strength and potentially damaging the screw thread and/or rod.